PAINT FILM BENDING TESTER

Harga : Rp 0.00 Rp 123.00

Brand : Qualitest,Yasuda Seiki,Toyoseiki,Drick

Stok : In Stock

Description
Review Product

PAINT FILM BENDING TESTER

Method / Standard : JIS-(K5400), K5600-5-1, ISO-1519

This tester is used to evaluate the bending endurance of paint and varnish coated film according to the cylindrical form mandrel method. The operator is to place the coated film testing board on the outer side and bending at a speed so that it takes 1 to 2 seconds to bend the testing board 180°. The operator is then to see cracks and peels of the coated film.

Spesifikasi

Model	No.514
Test Plate	150 × 50 × T0.3 mm or Less
Bending Angle	180°
Mandrel Diameter	φ2, φ3, φ4, φ5, φ6, φ8 and φ10 mm: 7 kinds
Supporting Plate Thickness	1, 2, 2.5, 3, 3.5 and 4 mm: 6 kinds
Dimensions/ Weight (Approx.)	W150 × D100 × H50 mm, 2 kg

TYPE1 Paint Film Bending Tester

Method / Standard : JIS-(K5400), K5600-5-1, ISO-1519

This tester is used to evaluate the bending endurance of paint and varnish coated film according to the cylindrical form mandrel method. The operator is to place the coated film testing board on the outer side and bending at a speed so that it takes 1 to 2 seconds to bend the testing board 180°. The operator is then to see cracks and peels of the coated film.

Spesifikasi

Model	No.514-TYPE1
Test Plate	100 × 50 × T0.3 mm or Less
Bending Angle	180°
Mandrel Diameter	φ2, φ3, φ4, φ5, φ6, φ8, φ10, φ12, φ16, φ20, φ25 and φ32 mm: 12 kinds
Supporting Plate Thickness	3.5, 6, 8, 10, 11, 12, 13, 13.5, 14, 14.5 and 15 mm: 11 kinds
Dimensions/ Weight (Approx.)	W150 × D100 × H50 mm, 2 kg

Paint Film Cylindrical Bending Tester Bending Machine for Testing Coating Elasticity

1.Maximum test piece width：60 mm

2.There are 12 stainless steel bars with different diameters: 2, 3, 4, 25, 5, 6, 8, 10, 12, 16, 20, 32 mm

3.The bending tester is designed according to GB/T 6742 and ISO 1519-93, which is suitable for the determination of the minimum diameter of the paint and varnish coating under the standard conditions, bending around a certain diameter of the cylindrical shaft, and without causing damage to the coating, It is expressed in mm

4.This is a very simple and rapid method for measuring the elasticity of coatings. Only the test plates of existing coatings are bent on the circular shaft of known diameter, and the cracking or damage of the coating is observed.

Product Description

Complies with: BS3900: E1, DIN 53150, DIN EN ISO 1519.

Used to test the resistance of a coating of paint, varnish or related product to cracking or detachment from a metal panel , after the panel has been bent around a cylindrical mandrel.

It can be used as a simple Pass/Fail test at a known diameter, or as a Paint of Failure test, by using successively smaller mandrels until cracking is observed.

Accepts up to 50mm wide and 1mm thick panels cam be tested. The following SS mandrels are supplied togerther:

2,3,4,5,6,8,10,12,16,20,25,32mm dia.

Procedure

Apply the paint film on sheet metal strips

Coat and dry film carefully to ensure reproducible results For testing,uniformly bend the coated samples over the bending mandrels within 1-2 sec at 180 degrees

Start with the largest bending radius,the test is continued until reaching the bending radius at which film shows crack.

Technical Datas

Net Weight:5.5 kg

Dimension230 x 170 x 100 mm

Shipping Weight:7 kg

Note

All products have been checked and packaged in good condition before shipping.

After your order is confirmed,the product will be sent to your hands for 7-13 workdays.

If you have any question, please feel free to contact with us . We will try our best to give you a satisfactory solution.

Untuk informasi dan pertanyaan silahkan hubungi marketing kami siap membantu menjawab kebutuhan yang anda cari

PT. Mora Anugerah Berkat (M.A.B)

Ph. (+62)021 7345.7064 / 7366.0160 Fax. (+62)021 7366.0160